|
|
Directory: Catalog > Boilers
> Munchkin Boilers > Munchkin Parts
Parts for the Munchkin T50M Boiler, Revision 2
We stock the most common Munchkin Boiler repair parts. We also will obtain special-order Munchkin parts from the manufacturer or from one of our other sources.
- Parts are listed in numerical order below. You can also view this list in a chart view with parts diagram.
- This series of the T50M Munchkin Boiler Revision 2 has a manufacture date after 12/20/06. If this is not your unit, please go to our main Munchkin Parts Page to find your unit.
Parts for the T50M R2 Boiler:
- 7000P-805: Plastic Tubing 3/16 in. ID (Blocked Vent Pressure Switch)
- 7250P-003: Gasket (Aluminum Elbow to Air Channel)
- 7250P-005: Gasket (Flame Rectification Probe / Spark Electrode)
- 7250P-019: ECO High Limit Sensor
- 7250P-049: Flame Rectification Probe (with Gasket)
- 7250P-059: Thermistor
- 7250P-069: Screw M4 X 8MM (Flame Rectification Probe / Spark Electrode)
- 7250P-070: Gasket (Burner)
- 7250P-080: Relief Valve
- 7250P-081: Water Pressure Switch (red dot, most common)
- 7250P-085: Combustion Blower (Blower Motor)
- 7250P-089: Thermodisc Flue 210 Degrees
- 7250P-091: LED Display Box with Ribbon Cable (Only if the main control board is 926.)
- 7250P-096: Water Pressure Switch (blue dot, less common)
- 7250P-144: Gasket (Aluminum Elbow to Combustion Blower)
- 7250P-145: Air Inlet Baffle
- 7250P-150: Blocked Vent Pressure Switch (new # 64980007)
- 7250P-151: Steel Push Retainer (Thermodisc Flue ECO)
- 7250P-152: O-Ring 007 (Blocked Vent Pressure Switch)
- 7250P-153: S.S. Hex Nut 10-32 (Blocked Vent Pressure Switch)
- 7250P-154: Hose Barb 1/4 X 10-32 (Blocked Vent Pressure Switch)
- 7250P-160: Ceramic Target Wall
- 7250P-161: Burner Door Refractory
- 7250P-169: Burner Door
- 7250P-170: Gasket (Burner Door to Air Channel)
- 7250P-178: Air Channel
- 7250P-204: Screw (Burner)
- 7250P-206: Screws Torx M5 x 22MM (Air Channel to Burner Door) - Bag of 5)
- 7250P-215: Hose Clamp for Condensate Assembly (new # 64980140)
- 7250P-216: Burner (with Gasket)
- 7250P-226: Blower Motor Gasket
- 7250P-311: PVC Black Tubing 1/8 ID (thermodisc Flue ECO)
- 7250P-332: LED Display Box with Ribbon Cable (Only if the main control board is 925.) - DISCONTINUED
- 7250P-352: Control Board Hold Down Clips
- 7250P-378: Fuse (Control Board)
- 7250P-421: Spark Electrode (with Gasket)
- 7250P-427: Gasket (Top Flue Exhaust Pipe)
- 7250P-444: Exhaust Manifold Tube
- 7250P-448: Dungs Gas Valve
- 7250P-460: Condensate Hose Assembly (Discontinued)
- 7250P-644: Gas Valve Adapter Plate, with Screws (new # 64980046)
- 7250P-646: PVC Tee Sch. 40 3/4 in. (Condensate Assembly)
- 7250P-647: Poly Plug 3.4 in. NPT (Condensate Assembly)
- 7250P-648: PVC Nipple Sch. 80 3.4 in. NPT (Condensate Assembly)
- 7250P-649: Cable Clamp (Condensate Assembly)
- 7250P-653: Spark Cable
- 7250P-696: 5 Pin Wiring Harness
- 7250P-697: 9 Pin Wiring Harness
- 7250P-700: Low Voltage Wiring Harness (10 Pin/20 Pin Main Wiring Harness, with Gas Valve Plug)
- 7250P-704: Screw M4 X 8MM (Ceramic Target Wall)
- 7250P-731: 926 Control Board Upgrade Kit (For units built before July, 2008 that have the 925 Control Board
- 7350P-008: 926 Control Board - For units built after July, 2008, or if the board has been previously upgraded from 925 to 926
- 7350P-009: Display Board for 926 Control (new # 64980136)
- 7350P-624: 24VAC Gas Valve Coil Only - Grey (discontinued, please order the complete gas valve assembly)
- 7450P-218: Condensate Neutralizer (formerly part # N1100)
- 7500P-067: Nut M6 (Burner Door)
- 7500P-091: Swirl Plate
- 7500P-094: O-Ring (Gas Valve Piping Assembly)
- 7500P-099: Screw M4 x 12MM (Gas Valve Piping Assembly
- 7500P-109: Washer M4 (Ceramic Target Wall)
- See Accessories: PC connection, vent kits, mesh screens, etc.
Download Literature: Loading times will vary depending on the speed of your Internet connection. After the download is complete, use your browser's back arrow to return to this page.
UPS is not picking up on Wednesday, 12/31/25
and Thursday, 01/01/26. Normal shipments
will resume on Friday. Happy New Year!
|
